MFinity Pro Microfiber Ceramic Coating Applicator Pads
Regular price
$5.99
MFinity Pro Ceramic Coating Microfiber Pads
MFinity Pro Ceramic Coating Pads are made with a premium 70/30 blend of microfiber. Premium microfiber fabric is wrapped around a plush, durable foam pad that delivers just the right amount of pressure to easily mold itself to the surface delivering the perfect amount of ceramic coating. They are side stitched two times to ensure that the edges never touch your paint and reduce the risk of scratching.
Due to rapid hardening, it is recommended to apply in smaller surface areas rather than one large section.
Ensure that you are using clean microfiber cloths for each step, and do not reuse suede applicators.
Make sure to keep the coated vehicle out of wet conditions while curing.
Maintenance
When maintaining and cleaning the vehicle, use a neutral PH soap to ensure longevity.
Only use touchless washes on your ceramic coated surfaces.
There is no need to wax the surface of your vehicles after coating has been applied.
Product Storage
Store all coatings in a cool, dry place.
Shelf life for an unopened bottle is 2 years.
Use within 6 months after opening.
Wipe drip tip after use and seal tightly to prevent clogging.
Do not refrigerate or freeze ceramic coatings.
WARNING: KEEP OUT OF REACH OF CHILDREN. USE IN WELL VENTILATED AREAS ONLY!
Always read instructions before use. May be harmful if swallowed. May cause skin & eye irritation. If swallowed please contact the poison control center or physician immediately. In case of eye contact, immediately flush with water, remove any contact lenses, continue flushing with water for 10 minutes. If irritation continues, acquire medical advice/attention.
Preserve is a 20% ceramic (SiO2) based waterless wash Nano ceramic coating spray designed to provide maximum protection for all-ceramic coated & non-ceramic coated surfaces. Preserve cleans and adds a slicker and super hydrophobic effect that lasts up to four months on coated surfaces and up to 2 months on non-coated surfaces. Preserve can be used on any nano-ceramic coating brand that has previously been installed.
Uses
Preserve was formulated to be used to protect paint, plastic, and vinyl wrap.
Hydrophobic effect
Acts as a stand-alone coating on uncoated surfaces
Enhances the color & finish
Extends the lifespan of nano ceramic coating
Less maintenance
Application Instructions
Prior to application, make sure all areas to be treated are free of large dirt particles or grit. For best results, apply on a cool surface, out of the sun. Simply spray a generous amount of Preserve on the surface, fold a microfiber towel in fourths, and lightly wipe in straight lines to remove dirt. Alternate to a clean side of the towel when used section gets too dirty. To attain a streak-free, slick finish after all dirt is removed, use a fresh dry towel to buff away any residue.
Preserve will start to cure within 20 minutes. Allow product to cure & harden for 12-24 hours to achieve the longest possible protection. Every time you need to clean or detail - Preserve it.
Disclaimer
MFinity makes no expressed or implied warranty & accepts no responsibility for any direct or indirect damages since the seller has no control over handling or use once sold.
Due to rapid hardening, it is recommended to apply in smaller surface areas rather than one large section.
Ensure that you are using clean microfiber cloths for each step, and do not reuse suede applicators.
Make sure to keep the coated vehicle out of wet conditions while curing.
Maintenance
When maintaining and cleaning the vehicle, use a neutral PH soap to ensure longevity.
Only use touchless washes on your ceramic coated surfaces.
There is no need to wax the surface of your vehicles after coating has been applied.
Product Storage
Store all coatings in a cool, dry place.
Shelf life for an unopened bottle is 2 years.
Use within 6 months after opening.
Wipe drip tip after use and seal tightly to prevent clogging.
Do not refrigerate or freeze ceramic coatings.
WARNING: KEEP OUT OF REACH OF CHILDREN. USE IN WELL VENTILATED AREAS ONLY!
Always read instructions before use. May be harmful if swallowed. May cause skin & eye irritation. If swallowed please contact the poison control center or physician immediately. In case of eye contact, immediately flush with water, remove any contact lenses, continue flushing with water for 10 minutes. If irritation continues, acquire medical advice/attention.
MFinity Vinyl Wrap Nano-Ceramic Coating (2 Years)
Regular price
$5.99
Mfinity Ceramic Coating for Vinyl Wrapis great for those looking to protect and enhance their vehicle's vinyl wrapped surface. MFinity Wrapcan remain durable for up to 2 years. Wrap will make cleaning easier and will protect from contaminants and ultraviolet damage. Like all MFinity products, Wrap is very user-friendly. This coating leaves matte vinyl with a dulled appearance while enhancing gloss finishes.
Uses
Wrap was formulated to be used to protect the vinyl wrap and paint protection surfaces.
Super-hydrophobic effect
Reduces orange peel
UV resistant & weather resistant
Enhances the color & finish
Extends the lifespan of the film
Less maintenance
A 50 ML bottle can coat 4 to 7 sedans with a gloss finish wrap, 3 to 5 sedans with a satin finish wrap, or 2 to 3 sedans with a matte finish wrap.
Safety Instructions: 1. Keep out of reach of children 2. Store at a cool dry place (<75 ºF) 3. Don't Mix with other products 4. Use a respirator and gloves during application
Application Instructions
Prepare the surface of your vehicle. Go over the surface with denatured alcohol to remove any residual oils.
Use a MFinity Applicator block with a Mfinity Microsuede Applicator wrapped around or the MFinity Pro Microfiber Applicator.
Shake the product well. Apply 6 to 8 drops to the applicator. Coat the entire pad so it is dampened with the coating.
Coat the entire panel in horizontal and vertical strokes. Make sure to coat the entire surface.
After 60 seconds smooth over the surface with a clean microfiber cloth using the same application technique and light, even pressure to remove any residual coating
Repeat step 5 after approximately 10 seconds with a second clean MFinity microfiber cloth to smooth out the surface.
Let cure for 30 minutes or less before next coating
If and when applying a second coat, use 2 - 3 drops of MFinity Wrap on the applicator pad.
Wrap will harden within 8 - 12 hours. However, full cure time is 3 to 4 days depending on weather conditions and temperature.
Wait at least 7 days after coating the surface before exposure to water, dirt, cleaners, or any other contaminants. Failure to do so may result in streaking and or staining.
MFinity makes no expressed or implied warranty & accepts no responsibility for any direct or indirect damages since the seller has no control over handling or use once sold.
Due to rapid hardening, it is recommended to apply in smaller surface areas rather than one large section.
Ensure that you are using clean microfiber cloths for each step, and do not reuse suede applicators.
Make sure to keep the coated vehicle out of wet conditions while curing.
Maintenance
When maintaining and cleaning the vehicle, use a neutral PH soap to ensure longevity.
Only use touchless washes on your ceramic coated surfaces.
There is no need to wax the surface of your vehicles after coating has been applied.
Product Storage
Store all coatings in a cool, dry place.
Shelf life for an unopened bottle is 2 years.
Use within 6 months after opening.
Wipe drip tip after use and seal tightly to prevent clogging.
Do not refrigerate or freeze ceramic coatings.
WARNING: KEEP OUT OF REACH OF CHILDREN. USE IN WELL VENTILATED AREAS ONLY!
Always read instructions before use. May be harmful if swallowed. May cause skin & eye irritation. If swallowed please contact the poison control center or physician immediately. In case of eye contact, immediately flush with water, remove any contact lenses, continue flushing with water for 10 minutes. If irritation continues, acquire medical advice/attention.
MFinity Pro Ceramic Coating Applicator Block
Regular price
$5.99
MFinity Pro Ceramic Coating Applicator Block
The MFinity Block is a stable and structured way to coat your vehicles' surfaces. Use an MFinity Microsuede Applicator around the MFinity Pro Ceramic Coating Applicator Block to apply your MFinity Coating to different areas of your vehicle evenly.
Due to rapid hardening, it is recommended to apply in smaller surface areas rather than one large section.
Ensure that you are using clean microfiber cloths for each step, and do not reuse suede applicators.
Make sure to keep the coated vehicle out of wet conditions while curing.
Maintenance
When maintaining and cleaning the vehicle, use a neutral PH soap to ensure longevity.
Only use touchless washes on your ceramic coated surfaces.
There is no need to wax the surface of your vehicles after coating has been applied.
Product Storage
Store all coatings in a cool, dry place.
Shelf life for an unopened bottle is 2 years.
Use within 6 months after opening.
Wipe drip tip after use and seal tightly to prevent clogging.
Do not refrigerate or freeze ceramic coatings.
WARNING: KEEP OUT OF REACH OF CHILDREN. USE IN WELL VENTILATED AREAS ONLY!
Always read instructions before use. May be harmful if swallowed. May cause skin & eye irritation. If swallowed please contact the poison control center or physician immediately. In case of eye contact, immediately flush with water, remove any contact lenses, continue flushing with water for 10 minutes. If irritation continues, acquire medical advice/attention.